STRINGLAB
← TennisWhere

STRINGLAB · Tennis stringing simulator

Stringing a racquet, start to finish

← 01

About StringLab

Why I built this

Hi, I’m the person behind StringLab and TennisWhere. I coach tennis, I play tennis, and I’m curious to learn everything about the game: how strokes work, how matches are won, and what the gear in our hands is really doing.

Stringing is one of those things every player depends on and very few of us ever see up close. Your racquet disappears into a shop and comes back feeling different, and the why stays a mystery. I wanted a way to understand it properly, so I built the tool I wished existed: a place to string a racquet yourself, step by step, and learn why each step matters, without needing a machine or a spare frame.

It’s free. If you spot something a stringer would do differently, or have an idea for what I should build next, I’d love to hear from you.

More about me →

How to string a tennis racquet, step by step

StringLab is a free 3D tennis stringing simulator. You pick a real frame, a string and a tension, then do the whole two-piece job yourself on a stringing machine: mount the racquet, pull and clamp every main, tie off, weave the crosses and finish. Each step explains why before you do it, and mistakes are explained the way a coach would on a real job.

The 9 steps

  1. Meet the machine. A stringing machine does three things: six posts support the frame so it can’t bend, the tension head pulls each string to an exact tension, and clamps hold that tension once the head lets go. The whole job is that rhythm, about 35 times.
  2. Choose a racquet. The frame sets the rules: the string pattern, written mains × crosses (an open 16×19 for spin and power, a dense 18×20 for control), and the tension range printed inside the throat. Stringing outside that range can void the warranty.
  3. Choose a string. Polyester is stiff, gives control and spin, and goes dead before it breaks. Multifilament and natural gut are softer and kinder to the arm. Synthetic gut is the inexpensive baseline.
  4. Set the tension. Lower tension pockets the ball longer for more power and comfort; higher tension gives more control and more shock. String polyester about 10% lower than a soft string. Some stringers add 1–2 lb to the crosses. Use a slow pull for gut and multifilament.
  5. Mount the racquet. Close the throat support first, then the head (6, then 12 o’clock), then the four side supports. Snug, not tight: over-tightened mounts can crack a frame.
  6. String the mains. Feed the string’s midpoint through the two centre mains and work outward, alternating sides and never more than three strings ahead on one side. For each string: thread it, pull to tension, clamp right against the frame, release the head. The two tie-off strings get about 20% extra tension.
  7. Tie off the mains. Run each tail to its tie-off grommet and knot it around the anchor string inside the hoop with a Parnell (Pro) knot or a double half hitch. Tighten knots by hand, toward the frame, and trim to about 6 mm.
  8. Weave the crosses. Install the crosses from the head down to the throat. The first cross sets the pattern; every cross after it goes over where the one above went under. Pull short loops quickly so the string doesn’t burn the mains.
  9. Finish and inspect. Tie off the last cross, release the supports evenly, straighten every string and check for weave errors. The frame should lift off as easily as it went on. Expect the bed to lose some tension in the first day: that’s normal relaxation.

Common stringing mistakes the simulator catches

Stringing questions

How long does it take to string a tennis racquet?
An experienced stringer takes 20–30 minutes on a modern machine. A first job usually takes an hour or more, mostly in weaving the crosses.
What tension should I string my tennis racquet at?
Stay inside the range printed on the frame, usually about 50–60 lb. Lower tension gives more power and comfort; higher tension gives more control. Polyester is usually strung about 10% lower than a softer string.
Should the mains or the crosses go in first?
The mains go in first, from the centre outward, so the frame is loaded symmetrically. The crosses follow from the head down to the throat.
What is two-piece stringing?
Two-piece stringing uses one length of string for the mains and a second length for the crosses, each with its own knots. It is the most common method and the one this simulator teaches.
How often should I restring my racquet?
A common rule is as many times a year as you play per week. Polyester loses its playability before it breaks, so restring it sooner.

Rather have a pro do it? Find a racquet stringer near you in Ontario, British Columbia, Alberta, Quebec, New York or Los Angeles.

Racquets are modelled from manufacturers’ product photos; TennisWhere isn’t affiliated with the brands shown. The simulator teaches the two-piece method with simplified physics.